DW3404 Stainless Steel Dry Well - These are most commonly used with pools and spas. Mounted in a tee in the water stream and probe mounted inside to monitor pool or spa temperature. 3/4” MNPT, 2 3/4” probe length. This...

Product DescriptionThe Cash Acme In-Line Check Valve is a NSF-61 certified general purpose, spring loaded Check Valve that prevents the reverse flow of water, oils and other fluids. Unlike the metal to metal check valves, the Cash Acme Check Valve...

Product DescriptionThe Cash Acme Y-Strainer utilizes a wire mesh screen to actively remove small solid particles from the flow of liquids or gases.The Cash Acme Y-Strainer may be installed horizontally or vertically in a pipeline to protect equipment such as...

Product Description1/2" Boiler Drain 87-0505; MPT, consists of a brass body construction with 1/2 in. (20mm) hose thread connection on outlet side, Teflon stem packing, and cast iron handwheel.Typical ApplicationsResidential hydronic systemsFeatures Brass Size: 1/2'' MPT Maximum Pressure: 200psi (13.8...

DW34 Stainless Steel Dry Well - These are most commonly used with pools and spas. Mounted in a tee in the water stream and probe mounted inside to monitor pool or spa temperature. 3/4” MNPT, 1 3/4” probe length. This...

Product DescriptionThe Cash Acme Heat Guard 110-HX Temperature Actuated Valve mixes hot and cold water to deliver reduced temperature hot water. The valve offers a high flow rate which reduces system pressure losses, and robust, low complexity construction. An adjustable...

Product DescriptionLegend Swing Check Valve 105-105Typical ApplicationsHydronic systemsFeatures Brass Size: 1''

Product DescriptionThe VU844A1003/U Actuator Fan Coil Valve Actuators is used in conjunction with the VU54S2016/U (Hi Presasure Valve 3/4" inch Sweat 3W), for controlling the flow of hot or chilled water in commercial HVAC equipment such as fan coil units,...

Product DescriptionThe HG110-D, a triple-listed thermostatic mixing valve, delivers water at a safe 120°F (49°C) or lower from all outlets, while allowing the water heater to be set at a germ-killing 140°F (60°C) or higher which aids in preventing the...

Product DescriptionLegend Swing Check Valve 105-104Typical ApplicationsHydronic systemsFeatures Brass Size: 3/4''

Product DescriptionThe Cash Acme In-Line Check Valve is a NSF-61 certified general purpose, spring loaded Check Valve that prevents the reverse flow of water, oils and other fluids. Unlike the metal to metal check valves, the Cash Acme Check Valve...

Product Description2000 Series High Quality Brass Ball ValvesTypical ApplicationsHydronic systemsFeatures Brass Size: 1/2'' NPT threaded connections Full port Adjustable packaging gland Pressure rated to 600 psi WOG and 150 psi WSP Maximum temperature 300°F (149°C)

Introducing Our Brand New Circulating Pumps: Elevate your wood boiler system to unprecedented levels of precision and performance with the Velo Series Circulation Pumps. Comes with Plug attached! 2 year warranty. High-Temperature Performance:The Velo Series is designed to thrive in...

Product DescriptionSharkBite U2008-0000 Check Valve 3/4” is a general purpose spring Check Valve that prevents the reverse flow of water. It can be installed horizontally or vertically, and it can be connected to copper, CPVC, and PEX pipes.Typical ApplicationsHydronic systemsFeatures...

Product Description2000 Series High Quality Brass Ball ValvesTypical ApplicationsHydronic systemsFeatures Brass Size: 1 1/4'' NPT threaded connections Full port Adjustable packaging gland Pressure rated to 600 psi WOG and 150 psi WSP Maximum temperature 300°F (149°C)

Honeywell VU54S2016/B 1" Three-Way Fan Coil Sweat Valve. The VU54 high pressure zone valves are used to control the flow of hot or chilled water in commercial HVAC equipment such as fan coil units, terminal reheat coils and convectors. IMPORTANT...

Product DescriptionThe Heatguard®115 is a large sized high flow rate Temperature Actuated Mixing Valve that mixes hot water with cold to deliver tempered water at a controlled pre-set temperature.The Heatguard®115 is intended for installation at water heater to distribute controlled...

Product Description The SharkBite Disconnect Tong is the easiest way to disconnect SharkBite fittings in hard to reach places where it can be tough to get leverage on the release collar. The Stainless Steel Disconnect Tongs are the perfect tool...

IW1203 Copper Immersion Well 1/2" MPT- These are most commonly used with Aquastats. 1/2” MPT, 3" max insertion/bulb length. Bulb diameter 3/8", Insulation depth 1". May be used with SKU: AQ11D18-1

Honeywell VU54S2016/B 3/4" Three-Way Fan Coil Sweat Valve. The VU54 high pressure zone valves are used to control the flow of hot or chilled water in commercial HVAC equipment such as fan coil units, terminal reheat coils and convectors. IMPORTANT...

Cash Acme SharkBite U2020-0000A 1" Check ValveSharkBite Check ValveA Connection System For Copper, CTSCPVC and PEX PipeThe Cash Acme SharkBite® fittings line presents a revolutionary solution to connecting water distribution pipe. Our SharkBite® Push-Fit Fittings are the fastest, easiest way...

Product DescriptionThe Cash Acme In-Line Check Valve is a NSF-61 certified general purpose, spring loaded Check Valve that prevents the reverse flow of water, oils and other fluids. Unlike the metal to metal check valves, the Cash Acme Check Valve...

Product DescriptionSharkBite U2008-0000 Check Valve 1/2” is a general purpose spring Check Valve that prevents the reverse flow of water. It can be installed horizontally or vertically, and it can be connected to copper, CPVC, and PEX pipes.Typical ApplicationsHydronic systemsFeatures...

Product Description The Kit includes a mixing valve (MV34S or MV34SB), sidearm and diagrams for easy installation Typical Applications Ideal for residential heating and plumbing applications MV34S Cash Acme HeatGuard® 110-D Tempering Valve Sweat intended for installation at the water...